UPVC Window Handle Replacement

Replacing a broken window replacement panes handle is a relatively easy task and with the right tools it can be done quite quickly. It's important to know what kind of handle you have as well as the size of its spindle before you purchase an alternative.

Older uPVC windows have handles with cockspurs, which have spurs that protrude to lock over a cockspur wedge striker plate. They can be right or left-handed and have to be replaced with the same handle.

What kind of lock or handle do I have

There are a variety of window handles made of upvc and locks, each with its own benefits and purposes. The kind of handle you choose will determine the ease to open your windows and whether or not the locking mechanism works as intended. As time passes, and with regular use, the upvc handles on your windows could get worn out and damaged. This makes them less secure and less effective. In certain instances, they might even fall off completely. It is crucial to fix the handles on your window made of upvc as soon as you notice they are falling off. This will help prevent burglaries, and keep your house secure.

It's a simple job that anyone can complete. With a few basic tools and the right information it's a simple procedure that should take no longer than a couple of minutes. It is important to know the kind of lock or handle you have on your window. This will help you select the appropriate double glazed replacement windows.

Inline Espagnolette Handles

They are typically located on the side of the window. They are flat and have an opening that engages the locking mechanism of the window frame. Inline upvc handles have spindles that run through the centre of the handle and into the window frame to operate the latch.

Cockspur Handles

These handles are usually found on older uPVC window frames. They have a distinctive, hook-shaped design. Cockspur handles are fitted with a single screw that is used to secure the handle to the frame and aren't as secure as other kinds of window handles.

Handles that turn and tilt

In contrast to other upvc handles the tilt and turn handles can be rotated to open the window and tilted inwards for ventilation. In general, they have a 7mm spindle at the back of the handle. They are available in both left and right handed versions.

When you are purchasing replacement handles for upvc it is essential to check the spindle length as not all are the same size. To test the length of your upvc handle simply drop something in the middle of the hole and measure how far it extends before it comes into contact with an obstruction. This is the length of the spindle that will be suitable for your window.

What is the spindle?

uPVC window handles function in a similar way like doors, turning the handle to operate an internal latch within the frame. The window is then opened and closed. The handles can become damaged, especially if they're used frequently or exposed to harsh environments. This could mean that you have to replace your uPVC handles on windows since they may not be able to operate the window properly for a long time.

There are many different types of uPVC handle options, including Espag, UPVC Window Handle Replacement Cockspur, and Spaded handles. They are designed to fit into the uPVC frames in a variety of ways. Each handle utilizes a specific spindle to secure the mechanism to the window. This is why it is important to know what kind of handle you have on your uPVC window so you can find the right replacement for it.

The base of the handle will tell you what kind of uPVC it is. A snap-in cover should be over the screw that holds the base of the handle in position. Take it off and you should be able see the second holding screw located at the opposite end of the base portion of the handle. Once both screws are removed you should be able to pull the handle away from the uPVC window.

Once you have removed the uPVC window handle, you will need to carefully remove the spindle that was previously attached to the locking mechanism. Note the length of the spindle. You'll need purchase a replacement with the same length as the original handle and the locking device.

The spindle wears out and cannot operate the locking mechanism. This could be due to corrosion, damage from frequent use, or the locking mechanism becoming looser. If this happens, it is necessary to replace the window handle and the locking mechanism to restore full functionality to your uPVC windows.

How do I get rid of the old handle?

double glazing window replacement handles can become damaged or broken over time. It is essential to fix them as quickly a possible to ensure your security. It is simple to replace a worn or damaged handle. The task can be accomplished in under an hour without the need for any special tools.

The first step in removing the old handle is to remove the screw that is located on the top of the base of the handle. Once the screw is removed, the handle will be pulled away from the base section. Another screw will be located at the base of the handle. This too can be removed. After these two screws have been removed, the handle will be removed from the window's base.

After removing the handle and align the fixing holes of the new handle with the existing holes in the window frame. There may be a little cap or sticker on the new handle, so remove the caps if needed, and then put the handle in place. It is essential to ensure that the handle is working after it has been installed. Turn the handle and make sure the lock mechanism is activated.

Espag handles come with a spindle which protrudes from the handle and slots into the multipoint locking mechanism that is on the window frame. Cadenza windows feature a blade with cutouts that are incorporated into the lock mechanism. Cockspur handles are long and hang over the frame of the window or the transom bar crossmember.

Once you have the new handle in place, you can insert the spindle into the window lock and then tighten it. Replace the snap-in cover and screw cap (if applicable) after the handle is fixed. The handle is now ready to use to use, so try opening and closing the window several times to ensure that it is working properly and securely.

How do I install the new handle?

It's not difficult to change the handle on your windows made of uPVC. The procedure is easy. All you require is a screwdriver and small amount of patience. First, ensure that the handle is not locked. Remove any screws visible. You could also replace them with screw caps. Once the handle is removed it is necessary to take an outline of the length of the spindle that extends from the back of the handle. This is crucial as it will determine the kind of handle you'll need to purchase.

Espagnolette handles made of uPVC are the most well-known type of handle. They feature a spindle that runs through the handle and operates a locking mechanism within the window frame. The handle releases the latch, allowing the window to open. As time passes and with regular use, espagnolette handles may be damaged or destroyed, making it necessary to find an alternative.

Cadenza handles are a different kind of uPVC window handle that is commonly used on tilt and turn windows. They have an elongated blade that functions as a multipoint locking mechanism within the window. They are more secure than the espagnolette handles because they are able to open from the inside. They can be replaced with the same method as espagnolette handles, however you must make sure that the new handle has an angled blade instead of flat ones.

Once you have decided on the correct handle to purchase, you can simply place the new handle to the existing screw holes and then screw it into place. After that, you should put the screws back on and verify that the new handle is working properly. You can do this by dragging the handle between the locked position to the unlocked one several times. If you encounter any issues, it could be worthwhile contacting a professional to see if they are able to assist in resolving the issue. They can offer advice on how to solve the issue in a quick and effective manner.