Reasons Your fiat punto keys 500 Key Fob Won't Work

A key fob for the fiat 500 flip key repair 500 is a convenient way to unlock the doors and get started the car. There are many reasons why the fob won't work. This includes a dead battery, water damage, receiver modules issues, and interference.

This listing is for an NEW replacement fiat 500 remote key replacement panda key fob replacement key fiat 500 (conversational tone) Flip Key Remote that appears similar to the Ilco brand. It needs to be professionally programmed (click here to find local automotive locksmiths). Includes lock, unlock, and trunk buttons.

Dead Coin Battery

A dead battery is the most frequent reason for your 500 key fob being inoperative. Modern key fobs have a limited range of operation, and should be within some feet of the car to operate. If you're not close to your vehicle, and you press the key fob button the car won't be able to respond, and will display the "Key Fob Not Detected" message in the instrument cluster.

If this happens If this happens, replace the battery in the coin-cell (Part Number CR2032) by a brand new one of a reliable brand, such as Panasonic Duracell or Energizer. They can be found in your local hardware store or on the internet.

After you've replaced the coin cell battery you can test it by standing close to your fiat 500 stolen without keys 500 and pressing the buttons. The car will flash its parking lights and the key fob should work the lock and unlock switches.

If the fob's remote doesn't work after replacing the battery, it may have water damage that stops it from connecting to the receiver module inside your vehicle. Water damage can happen in a variety of ways, from a light splash to submerging the fob salt water at the beach. If you suspect that your fob has been exposed to water, you can place it in a bag of rice to draw out the moisture. If this does not work, you'll require your fob to be replaced by an auto locksmith or dealer.

Water Damage

Damage to the water supply can occur if you immerse the fob in the ocean or wash it in a washing machine. Saltwater can cause the circuit board to short and then die. It's not good to let the fob get wet however, don't give it up even if you accidentally drop the fob in water or fail to remove it from your pocket.

Take the battery off first. Clean the electronic chip with isopropyl alcohol or a similar product and dry it thoroughly before replacing the battery. Check the fob to verify if it's functioning. If the key doesn't function it could need to be programmed again. This is usually done by an auto locksmith or dealer.

If the key is older and has never been programmed to your car It will most likely need to be replaced completely. A professional locksmith for cars can carry out this simple task. The locksmith needs to cut the key to match the ignition of your vehicle. The locksmith will also have to reprogram your fob into the car's system. This is a cost-effective and quick procedure that can be completed in the same day.

Receiver Module Issues

One of the main reasons your 500 key fob may stop functioning is because it's out of range. The remote usually has 30 feet of range or less, and if it's too far from your car, it will not respond to your commands. It's easy to remedy this by moving your remote closer to your car until it responds.

If you've replaced the battery in your coin (commonly known as"button" or "button" or "watch") and your fob still won't work, it could have an internal circuit board issue. In the majority of cases, reprogramming your fob can resolve the issue. You can find directions on how to do this for all vehicles by searching YouTube or reading the owner's manual.

You may have to replace the metal clips that hold the coin battery in place. If they loose tension, it can prevent the battery from being properly seated and cause your remote to malfunction.

In rare cases the fob could be disconnected from your vehicle because of software or hardware issues. This could be a huge issue, but you are able to frequently fix this issue by visiting an auto locksmith to reprogram your fob. In some instances they may have to reinstall the program in your body control module, too.

Interference

In addition to a dead coin battery The key fob might not be able to transmit or receive the signal due to interference. This is possible when the key fob is located near a radio transmitter (cell phones or radar detectors) or any other source of electromagnetic radiation. The key fob could not function because of a weak connection with the buttons, water damage or damage to the internal chips.

If your key fob suddenly stopped working, or you've tried everything at home to resolve it (e.g. You may have a faulty 500 receiver module in the event that you've tried replacing the battery, reprogramming or using an alternative key fob. The receiver module, located under the dashboard, receives radio frequency signals from your key fob. It converts them into electronic commands that the vehicle interprets.

There is a simple way to reset the 500's on-board system, including the keyfob. Disconnect the battery of 12 volts for about 15 minutes by taking off the negative cable first then the positive cable. Reconnect the battery. This will erase any remaining electricity, and restart the computer in your car. This can help get your key fob working again. If the issue persists, you should consult an expert technician. They will be able to identify the root of any issues.